Search Rainbow Brite's Blog

Monday, July 15, 2013

How to: Make a Rainbow Brite Style Display Box

How to make a Rainbow Brite Style doll box
Rainbow Brite Dolls in custom boxes
This is a cross post from the main website tutorial here.

Tools you will need to re-create the box
a: Utility Knife (for heavy cutting)
b: Xacto Knife (for detail cutting)
c: Ruler/yard Stick
d: pencil
e: Scoring Board (for making creases)
f: rubber gloves (to minimize the oil from your hands from over handling.)
g: glue
h: Velcro with adhesive back
i: silica packets (optional)
j: poly bags/head wraps for dolls (optional)

To re-create my Rainbow Brite Doll box, I used an old one to get the measurements and parts.

The box consisted on the following:

A: 1 Box
B: 1 Cardboard insert
C: 3 Lengths of plastic coated wire.
D: 1 clear plastic window (9 ½ in x 6 ½ in)



To make each box, I need a hard template/stencil to re-use as I need a new box. I decided to buy some foam core board from my local hobby shop for this.

I clamped the old box down flat onto the foam core board and traced the old box onto the surface. The clamps keep the box from moving as I go around with my pencil. Include the center/window of the box as well. Once done I remove the old box and use a box cutter/utility knife to cut out the shape. It is best to use the Xacto Knife for the window, as you need to be detailed with the curve of the shape if you intend to duplicate the same curve.




If you do not have an old box to make your template from, you will find measurements below for what I used.
Insert Measurements (Click to enlarge)
Box Measurements (click to enlarge)



Now lets start making your box.
You need the following:

A: Heavy Poster Board (minimum 18 3/8 in x 18 3/8 in is needed for each box)
B: ¼ sheet cake board (or 10 x 11 6/8 in corrugated card board)
C: Spool of clear plastic coated wire (9 ½ inch lengths are used to mount doll)
D: Transparency Sheets



The box itself is made out of a thick poster board I got from an office supply store. Chip board is too thick, and regular poster board is too thin. The heavy poster board is the closest to the real box weight I was able to locate. You can make one box per sheet of poster board.

To create your box, clip the template to the poster board. I find putting it next to the corner of the paper will assure you get a straight and even line for two sides of your board.




After you have traced the outline, un-clip the template, and use a yard stick and the utility knife to get a straight cut around the other sides of the outline, so you have a rectangle. The other parts of the box are triangles, so use a ruler to assure those straight cuts, and finish cutting away the other negative areas of your outline.




Now that you have your box shape cut, you need to make the creases. The best tool for this is a “Scoring Board”. Martha Stewart has a nice large one available at most craft stores.




To score your box, lay the box on the scoring board, and using it's tool, press firmly and follow the groove from one end of the box to the other. Do that for all areas that need to be creased. This includes the folds at the top and sides (see picture)



When you make a crease it will darken the area but this will not be visible when you fold the box.

Next cut the window out of the center of the box if you haven’t done so already, and the extra cut in the closing flaps. You should know where this is now that you have made your creases.



Next you will need to glue down your window. The transparency sheet is too wide to fit as it is, so you will need to cut off the extra width. Once cut in to the correct size, draw a line of glue around the inner window of the box about a half inch. Once it's done, place the clear transparency film down over the window. Press down on the glue trail, and move your finger out away from window. This will spread the glue out and make sure it lays flat.




Lay the box down and let the glue dry.

After it has dried, fold the box on the crease you created until it meets the end. Draw a line of glue along the end and use a pair of clips to clamp the two pieces together. Make sure the seam is flat and the glue is not leaking out the cracks. You can better assure the seam if you used two rulers on either side of the board and clamp that down so that it's being held down from one end of the box to the other.



If you don't do this, you just need to hold down the seam by hand until it sticks enough on it's own and the clamps on the ends will keep it from coming apart.

While this is drying, you can work on the insert.

The insert for the box was originally a colored piece of very thin cardboard, but I wasn't able to duplicate this. Instead I used ¼ sheet cake boards. It is the correct width. You will need to trim off the extra length from the top.




Next comes the detail cutting for the insert. To assure the proper folds to fit in the box you will need to make a series of cuts in the back of the board (the brown part). Only two have to go all the way through the board. The others are only for the folds, so only have to be through the brown part.



You also need to punch a few holes through the cardboard too. These holes are what the wire goes through to mount the doll.

Depending on what doll you are mounting you may need more then two. All of the box inserts will need to hold the doll body. You will need extra parts to hold hair. For example the one I am working with is for “Rainbow Brite”, and in addition to holding her to the board, I also need a wire and holes to hold back her ponytail. Also, if your doll has a sprite, you may need to punch a set of holes to mount the sprite.

After all boards are cut and the box is dried, it's time to put the box together.

Fold in the flaps of the box and secure the box with Velcro. This way you can open the box later to adjust or add items as you find them.

Next cut wire, 9 ½ to 10 inch lengths.



Before mounting your dolls you may want to adjust their hair and wrap them. If you do this, you can use 4 – 5 inch poly backs cut into 2 inch rings to wrap around their heads and keep their bangs down.

Once you know your doll is ready, put the wire under the dress and out the sleeves. Feed the wire around the back of the doll and into the holes you punched in the center of the board. Turn the board and doll over and twist the wire firmly. When you turn the board back over the doll is now firmly mounted in the middle of the board.




Next, use another length of wire to secure the doll's hair if it needs it the same as you secured the body of the doll.

Now, secure the doll's sprite if available.


Lastly, slide the cardboard insert with mounted doll into the box.
Rainbow Brite and Twink reboxed!
Secure the other end of the box with Velcro. Add a silica packet if you like to keep away moisture, and you are done.  

No comments:

Post a Comment